forked from Bougakov/Micromake-D1-3D-printer
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathFirmware settings (factory, after EEPROM reset).epr
1 lines (1 loc) · 5.13 KB
/
Firmware settings (factory, after EEPROM reset).epr
1
<?xml version="1.0" encoding="utf-8"?><Repetier-Firmware-EEPROM><epr pos="75" type="2" value="250000">Baudrate</epr><epr pos="1028" type="0" value="0">Language</epr><epr pos="129" type="3" value="0.000">Filament printed</epr><epr pos="125" type="2" value="0">Printer active</epr><epr pos="79" type="2" value="0">Max. inactive time</epr><epr pos="83" type="2" value="360000">Stop stepper after inactivity</epr><epr pos="11" type="3" value="100.0000">Steps per mm</epr><epr pos="23" type="3" value="200.000">Max. feedrate</epr><epr pos="35" type="3" value="40.000">Homing feedrate</epr><epr pos="39" type="3" value="20.000">Max. jerk</epr><epr pos="133" type="3" value="0.000">X min pos</epr><epr pos="137" type="3" value="0.000">Y min pos</epr><epr pos="141" type="3" value="0.000">Z min pos</epr><epr pos="145" type="3" value="90.000">X max length</epr><epr pos="149" type="3" value="90.000">Y max length</epr><epr pos="153" type="3" value="300.000">Z max length</epr><epr pos="891" type="1" value="70">Segments/s for travel</epr><epr pos="889" type="1" value="180">Segments/s for printing</epr><epr pos="59" type="3" value="1000.000">Acceleration</epr><epr pos="71" type="3" value="2000.000">Travel acceleration</epr><epr pos="881" type="3" value="210.000">Diagonal rod length</epr><epr pos="885" type="3" value="92.000">Horizontal rod radius at 0,0</epr><epr pos="925" type="3" value="90.000">Max printable radius</epr><epr pos="893" type="1" value="100">Tower X endstop offset</epr><epr pos="895" type="1" value="100">Tower Y endstop offset</epr><epr pos="897" type="1" value="100">Tower Z endstop offset</epr><epr pos="901" type="3" value="210.000">Alpha A(210):</epr><epr pos="905" type="3" value="330.000">Alpha B(330):</epr><epr pos="909" type="3" value="90.000">Alpha C(90):</epr><epr pos="913" type="3" value="0.000">Delta Radius A(0):</epr><epr pos="917" type="3" value="0.000">Delta Radius B(0):</epr><epr pos="921" type="3" value="0.000">Delta Radius C(0):</epr><epr pos="933" type="3" value="0.000">Corr. diagonal A</epr><epr pos="937" type="3" value="0.000">Corr. diagonal B</epr><epr pos="941" type="3" value="0.000">Corr. diagonal C</epr><epr pos="1024" type="3" value="0.000">Coating thickness</epr><epr pos="808" type="3" value="0.000">Z-probe height</epr><epr pos="929" type="3" value="5.000">Max. z-probe - bed dist.</epr><epr pos="812" type="3" value="5.000">Z-probe speed</epr><epr pos="840" type="3" value="40.000">Z-probe x-y-speed</epr><epr pos="800" type="3" value="0.000">Z-probe offset x</epr><epr pos="804" type="3" value="0.000">Z-probe offset y</epr><epr pos="816" type="3" value="0.000">Z-probe X1</epr><epr pos="820" type="3" value="0.000">Z-probe Y1</epr><epr pos="824" type="3" value="0.000">Z-probe X2</epr><epr pos="828" type="3" value="0.000">Z-probe Y2</epr><epr pos="832" type="3" value="4.300">Z-probe X3</epr><epr pos="836" type="3" value="0.000">Z-probe Y3</epr><epr pos="1036" type="3" value="0.000">Z-probe bending correction A</epr><epr pos="1040" type="3" value="0.000">Z-probe bending correction B</epr><epr pos="1044" type="3" value="0.000">Z-probe bending correction C</epr><epr pos="880" type="0" value="0">Autolevel active (1/0)</epr><epr pos="106" type="0" value="1">Bed Heat Manager</epr><epr pos="107" type="0" value="255">Bed PID drive max</epr><epr pos="124" type="0" value="80">Bed PID drive min</epr><epr pos="108" type="3" value="196.000">Bed PID P-gain</epr><epr pos="112" type="3" value="33.020">Bed PID I-gain</epr><epr pos="116" type="3" value="290.000">Bed PID D-gain</epr><epr pos="120" type="0" value="255">Bed PID max value</epr><epr pos="1020" type="0" value="0">Enable retraction conversion</epr><epr pos="992" type="3" value="3.000">Retraction length</epr><epr pos="1000" type="3" value="40.000">Retraction speed</epr><epr pos="1004" type="3" value="0.000">Retraction z-lift</epr><epr pos="1008" type="3" value="0.000">Extra extrusion on undo retract</epr><epr pos="1016" type="3" value="20.000">Retraction undo speed</epr><epr pos="200" type="3" value="150.000">Extr.1 steps per mm</epr><epr pos="204" type="3" value="30.000">Extr.1 max. feedrate</epr><epr pos="208" type="3" value="10.000">Extr.1 start feedrate</epr><epr pos="212" type="3" value="4000.000">Extr.1 acceleration</epr><epr pos="216" type="0" value="1">Extr.1 heat manager</epr><epr pos="217" type="0" value="150">Extr.1 PID drive max</epr><epr pos="245" type="0" value="60">Extr.1 PID drive min</epr><epr pos="218" type="3" value="24.0000">Extr.1 PID P-gain/dead-time</epr><epr pos="222" type="3" value="0.8800">Extr.1 PID I-gain</epr><epr pos="226" type="3" value="80.0000">Extr.1 PID D-gain</epr><epr pos="230" type="0" value="255">Extr.1 PID max value</epr><epr pos="231" type="2" value="0">Extr.1 X-offset</epr><epr pos="235" type="2" value="0">Extr.1 Y-offset</epr><epr pos="290" type="2" value="0">Extr.1 Z-offset</epr><epr pos="239" type="1" value="1">Extr.1 temp. stabilize time</epr><epr pos="250" type="1" value="150">Extr.1 temp. for retraction when heating</epr><epr pos="252" type="1" value="0">Extr.1 distance to retract when heating</epr><epr pos="254" type="0" value="255">Extr.1 extruder cooler speed</epr><epr pos="246" type="3" value="0.000">Extr.1 advance L</epr></Repetier-Firmware-EEPROM>